Brakelight switch for Magura handlebar master cylinder

This is a compatible replacement for the original part which is no longer available.

 This part is due back in stock soon, call 01484 841395 to reserve yours

39741101-z 39741101 GU39741101 39 74 11 01
 3974 1101 3974.1101 39.74.11.01

Reconditioned Valeo starter motor and solenoid in black and silver finish. Professionally reconditioned and sold with a 12 month guarantee. This is a suitable replacement for Bosch 8 or 9 tooth Guzzi starter motors. Minor modification may be required on some pre 1990 models to make room for the solenoid. Please note that this item may be fitted to Loop frame models with some modifications as described in Guzziology. See , see this link for the modifications required to fit a Valeo starter to a 4 speed model.

This is an exchange only item, we can supply these before receiving your exchange unit subject to a refundable deposit so you can keep your bike on the road. See ELC10737 for the refundable deposit. Send your old starter motor to our registered address. NB In case of starter motor problems do not tap the casing as this will certainly cause it to fail. See SSA08075 for mounting bolts. Also known as Guzzi ref. 30730710
Do not remove second nut from terminal posts when fitting - this nut is required to hold the terminal in place

Supercedes Guzzi refs. 12730705, 14730554 and 14730705

 30730711 GU30730711 30 73 07 11
 3073 0711 3073.0711 30.73.07.11

Neutral indicator switch

 Availability varies on this part, check availability

 12207200 GU12207200 12 20 72 00
 1220 7200 1220.7200 12.20.72.00

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with standard 3 Ohm 12 volt coils and can be used to replace points or Motoplat ignition on models with Saprisa charging systems. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Eliminates vague timing due to worn distributors on big twins. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. Once fitted no further adjustment should be necessary. See this link for fitting instructions. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA31165

 This part is available by special order, request a quote

Brand new genuine Valeo starter motor and solenoid suitable as a direct replacement for Guzzi Valeo and Bosch 8 or 9 teeth starter motors. You may need to fit hex headed neutral switch bolts on some pre 1990 models to make room for the solenoid. Our part number for the bolt is SSA06016
Please note that this item may be fitted to Loop frame models with some modifications as described in Guzziology, also see https://www.thisoldtractor.com/moto_guzzi_loopframe_starter_-_how_to_replace_the_magneti_marelli_starter_with_a_valeo.html for advice on this upgrade.

This is a genuine Valeo starter made in the EU- please do not confuse with the cheap Chinese copies that sometimes appear on eBay.

Supercedes Guzzi refs. 12730705, 14730554 and 14730705

Please note you can get a discount of £30 on this item if you part exchange your existing faulty starter motor. See ELA30837 for less expensive alternative part

 This part is due back in stock soon, call 01484 841395 to reserve yours

 30730711 GU30730711 30 73 07 11
 3073 0711 3073.0711 30.73.07.11

Complete round 203mm left hand dip (UK spec) headlight unit with bulb. Black body with chrome rim.

Due to the scarcity of LH dip Italian made headlights we have sourced this reasonably priced alternative which is similar in size to the headlamp used on V50 and T3 models. Supplied complete with headlight bulb. Headlamp is slightly larger than stock so some repositioning of the headlamp brackets may be required. Please note there is no pilot light with this headlamp and thread size for bolt fixing holes is M8. This is a smaller thread than the M10 thread on T3 indicator stems.

 This part is available by special order, request a quote

Complete round black headlight with chrome rim, complete with bulb and pilot light. Right hand dip non-UK spec.

This light will fit Le Mans Fairing FAA99575

 This part is available by special order, request a quote

Chrome finish plastic horn cover

 Sorry, this part is no longer available.

 31744765 GU31744765 31 74 47 65
 3174 4765 3174.4765 31.74.47.65

Cut out switch, threaded body. Used as sidestand switch on big twins and clutch cut out switch on V7 series small twins and Breva 750

 This part is available by special order, request a quote

 29759150 GU29759150 29 75 91 50
 2975 9150 2975.9150 29.75.91.50

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with 12 volt 3 Ohm coils ELA14500 (big twins) and can be used to replace Digiplex on models with Ducati charging systems where the bike is converted to carburettors. This kit is just an ignition system, it will not control fuelling. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Once fitted no further adjustment should be necessary. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. See this link for fitting instructions. Some bikes may need at least one additional spacer to allow enough clearance for alternator cover to fit once pickup is fitted. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA14500

 This part is available by special order, request a quote